Sensitive Analysis of Tuned Mass on High Cycle Fatigue Safety Factor of Crankshaft

Document Type : Original Research Article


Aerospace Research Institute, Ministry of Science, Research and Technology, Tehran, Iran


Torsional vibration (TV) is one of the major issues and very important calculation for the safe running of internal combustion engines, specifically crankshaft. The properties of parts connected to the crankshaft have significant effect on vibration of the system as well as the crankshaft life. Initial selection of this part is usually specified based on engine designer experience and also the torsional vibration calculation of the crank train. In this paper, the focus is to find optimum tuned mass to connect to the crankshaft from the damper side using CAE tools. It is a mounting disk at the free end of the crankshaft named tuned mass. Therefore, the effect of tuned mass inertia on design criteria, especially crankshaft life, was investigated. The results show high sensitivity of high cycle fatigue safety factor of crankshaft to tuned mass. Therefore, adding a suitable tuned mass to the system can increase the crankshaft life, when needed. The results were presented in the paper in detail.


Main Subjects

[1]   Mendes, A. S., Meirelles, P. S., and Zampieri, D. E., "Analysis of torsional vibration in internal combustion engines: modelling and experimental validation," Proceedings of the Institution of Mechanical Engineers, Part K: Journal of Multi-body Dynamics, 222(2):pp. 155-178, 2008.
[2]   Nestorides, E. J., ed. A handbook on torsional vibration. Cambridge University Press, 1958.
[3]   Wilson, WK.,Practical solution of torsional vibration problems: with examples from marine, electrical, aeronautical, and automobile engineering practice.,Chapman & Hall; Vol. 2, 1956.
[4]   Hafner, KE. and Maass, H.,Theorie der Triebwerksschwingungen der Brennkraft maschine, Wien-New York;Vol. 3, 1984.
[5]   Chen, S.K., and Chang, T.,"Crankshaft torsional and damping simulation—an update and correlation with test results," SAE transactions,pp. 964-985, 1986.
[6]   Larmi, M. "Torsional vibration calculation and engine damping," Proceedings of international congress on combustion engines (CIMAC),pp. 96-105, 1988.
[7]   Boysal, A., and Rahnejat, H., "Torsional vibration analysis of a multi-body single cylinder internal combustion engine model," Applied Mathematical Modelling, 21(8): pp. 481-493, 1997.
[8]   Ma, ZD. and Perkins, NC.,"An efficient multibody dynamics model for internal combustion engine systems." Multibody system dynamics, 10(4): pp. 363-391, 2003.
[9]   Desbazeille, M., Randall, RB., Guillet, F., El Badaoui, M. and Hoisnard, C. "Model-based diagnosis of large diesel engines based on angular speed variations of the crankshaft," Mechanical Systems and Signal Processing, 24(5): pp. 1529-1541, 2010.
[10]Han, HS., Lee, KH. and Park, SH. "Parametric study to identify the cause of high torsional vibration of the propulsion shaft in the ship," Engineering Failure Analysis, 59(1), pp. 334-346, 2016.
[11]Guo, Y., Li, W., Yu, S., Han, X., Yuan, Y., Wang, Z. and Ma, X.,"Diesel engine torsional vibration control coupling with speed control system," Mechanical Systems and Signal Processing, 94 (1): pp. 1-13, 2017.
[12]MSC ADAMS. Documentation and help, Using Adams/Engine, 2005.
[13]AVL LIST GmbH. AVL Excite Designer, Theory Manual Version 7.0.3, October 2007.
[14]Milasinovic, A., Filipovic, I. and Hribernik, A. "Contribution to the definition of the torsional stiffness of the crankshaft of a diesel engine used in heavy-duty vehicles." Proceedings of the Institution of Mechanical Engineers, Part D: Journal of Automobile Engineering, 223(7): pp. 921-930, 2009.
[15]IACS UR M53, International Association of Classification Societies (IACS) Unified Rules UR-M53 for the calculation of Crankshaft Design Strength Assessment for I.C. Engines 1986 (Rev.1, Dec 2004).